WEBSITE UTK EUROVOX TOOLBAR TCB.CC (
CLICK HERE)
WEBSITE UTK EUROVOX (
AFTERDAWN.COM )
u.name: nas5359
p.dss: a(i/c)
First of all your USB adapter should have come with a disk as you will need to install a driver for it.I am on XP but it can't be that much different to reset a port no.:Connect up your box as you've described.Start / Control Panel / Administrative Tools / Computer Management / Device Manager
On the right hand side of screen, double click on Ports (COM & LPT). You should see your Serial to USB listed now. Double click on this and under the General Tab make sure the device is set to enabled. Next, under the Settings Tab, click on the Advanced button and set to COM3. Save and apply your changes.Now launch the firmware and flash the box.
How to install and powerscan Eurovox.Tutorial for Eurovox 1, 2 and Max Written mainly for the EuroVox 2 but basically the same for all. For these boxes all you need is the dabbaman/dnupman program and a null modem serial cable (same as for dbox), Cable feed and a TV obviously, and you will need the relevant firmware from our download section.
1; Connect cable input to the RF in socket on your eurovox, Also connect box to your pc with null modem cable and also to your TV with scart. And lastly insert the power lead and switch on.
2; Open the dabbaman/dnupman program and confirm you have the correct com port, then select your firmware depending on the model of your box. ie; EV1 = eurovox with 1 scart, EV2 = eurovox with 2 scarts and EVMAX = latest model.
3; Apply power to the box and wait untill (----) appears on the front. If your box has been flashed before it wont display this, it'll just show 4 normal digits.
4; Click on download in the top half of the dabbaman/dnupman window. Then click start in the following window. If your box has not been flashed before it will say (system reset), when this happens reboot the box by removing and reapplying the power lead. If box has been flashed before do not remove power lead, just wait a moment and it will start downloading. If you are trying to flash an EV2 and you get a message saying "this firmware is not fit for your receiver", you must flash with the (EV2 for firmware error) flash.
5; The firmware should now be flashing to the box. (dnld) will appear flashing on the front display. the process takes a few minutes so be patient.
6; Once flash has completed (0000) will appear on front of box.
7; If this is the first time the box has been flashed your TV you should have the user installation screen with an info window saying (please check your cable status) press the exit button on your remote and proceed to step 8. If the box has been flashed before you will have to press the menu button then highlight config then clear data followed by pin no of 0000. In the next screen erase all channels should be highlighted then press the ok button twice. Once the "wait to delete all channels" window has disappeared press the exit button. Now highlight the installation menu and press ok followed by the pin no again.
8; Now press the blue button (powerscan) (the colour options on the remote and on screen differ for the EVMAX this will be the yellow button) this will open another smaller window with the heading "full power scan". If you are on the T/W network press the OK button, if however you are on the NT! network you will have to highlight within the window the first entry for symbol rate, usually (6.952) (for sheffield use this frequency)and edit this to (6.887)then press OK. The box will now scan all frequencies and find all active transponders for your area, Then it will scan them all for channels. This can be a long process, So go and have a cuppa and a read of your newspaper.
9; If everything has gone to plan you should now have channels, when you go to an encrypted channel you wll usually get the message "please wait updating code" it is important you stay on this channel until it clears, as this is the box intercepting the latest encryption keys. Allow a few minutes for this process to happen, I would say no longer than 10.Now for the pain in the ass part, organizing your channels into favourites. The way i did it was to add all the general channels to (fav1) sports & movies to (fav2) kids & music to (fav3) and news & documentary to (fav4). Adult and ppv stuff I put in (fav2) after everything else. Once all this was done I changed the names of the fav groups within favourite manager. Remember your pin no to get into any settings is 0000. Or if you've changed it and somehow managed to forget it you can use 1004. I think it would be a good idea for all members to upload their channel data to the forum after everything has been organized into favourites, stating their area and provider. This will make it easier for others in future. Also I have noticed that the CC's occasionally mess around with channels and transponders, in which case certain channels may be missing from time to time. By doing an autoscan (red button) within the installation menu you will pick these channels back up again and it shouldn't affect the layout of your favourites much unless the broadcast frequency of the channel changes. In this situation the channel will be found again by doing an autoscan but afterwards will only be found from the main channel list that you access by pressing the TV button. Channels that were missing before the autoscan are usually found near the end of the channel list.
3. Backing up your channel data.Run the loader util.In the 'Channel data' section at the bottom, click the 'browse' button and choose a name and location for the channel data file.Click the 'Upload' button and all channel settings will be downloaded and saved.
4.Group the channelPress 'MENU' and choose channels and click 'Add Favorites' press Ok...and follow instricution given.
The latest firmware on aug 2008 was UFL_MaxV_Kuro3 18/4/08.
The symbol rate you need to use is 6.952. ( for Virgin Media/Sheffield) In factory default setting.
To change PC port..Right click on MyComputer > Manage > Device Manager > Ports > Right Click on RS232 serial > properies > Advanced > change to COM 1 - 3 > Save > Done!!!!
Problems with your PC/Laptop not recognising your eurovox.
To see which port your USB adapter is connected to, connect your USB adapter and follow the following instructions:
1. Go to the Start Menu
2. Right click on "My Computer"
3. Select "Properties"
4. Click on the "Hardware" tab
5. Click on "Device Manager"
6. Click the + sign next to "Ports (COM & LPT)"
7. One of the listed ports should indicate which port your USB adapter is connected to (e.g. COM1, COM2, COM3, etc.)
8. Go back to your map software program that you use to transfer data and make sure it is looking at the correct port.
9. You should be able to transfer data once the correct port is selected
If you need drivers go here
http://www.gilsson.com/usb_drivers_download.htm
Follow my advice to step 7. Locate your USB Adapter (port *)
Right click on that port and select properties. Then select port settings, then select advanced. At the bottom of that tab will be a drop down box with the port selected (port * in your case). Use the drop down to select another port (eg 1, 2 or 3). If the port you want to use is already allocated to something else, you can use the same procedure to reassign that port after you have finished.
Save the selections in the usual way. The USB converter will be permanently assigned to the port you selected.
1. Manual Scan on Individual Frequency :-
The easiest way to get an individual channel back is to check the Frequency of the affected channel, by pressing Info button twice on the affected channel and noting the Frequency - then go to Menu - User Installation OK and enter 0000 - when the Frequencylist appears, with arrow key scroll to the frequency number (example 507.000 Mhz) which will be highlighted, press OK and a Tick will appear in channel No:- to the left of Frequency number, now press blue button to Manual scan on that frequency, screen will go blank approx 90 seconds and an information box will appear stating what has been found wait until cleared then your channel should now be working correctly.
2. Auto-Sort On/Off :-
Menu - Installation - User Installation -OK - 0000 and press yellow button (Powerscan) and scroll down to bottom and turn Fav Sort to Off
1. Set time using GMT.
2. Go to installation, user installation.
3. Press red button to preform an autoscan.
4. When autoscan completes, IMMEDIATELY go to time settings again.
5. Make sure time is still correct.
6. Turn GMT off.
7. Press blue button to save and exit.
.
Masakan ayam masak merah..
